Kakute F7 & Tekko32 4x35A 4-in-1 esc (BLHeli 32) Combo

$100.00

Powerful flight controller board and associated 4-in-1 BLHeli32 ESC, runs the complete ArduPilot flight-stack and drives 4 motors up to 35A each. Supports DSHOT1200 out of the box.

Tom’s comment: 100 bucks for a fully compatible high-quality ArduPilot F7 FC with 4x 35A ESCs is a steal!

 

 

Description

Kakute  F7

The Holybro Kakute F7 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and on-screen display (OSD) in one. The Kakute F7’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy.

Features
• Supports Betaflight, Butterflight, Cleanflight and Ardupilot
• Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
• Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
• High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.
• Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
• 2 oz. copper PCB allows up to 120A maximum continuous current.
• Dedicated bootloader button for easy firmware flashing.
• Low-profile design fits into even very compact frames.
• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
• Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
• Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications
• MCU: STM32F745 32-bit processor
• IMU: ICM20689 (SPI)
• Barometer: BMP280
• Current Sensor: Approximately 130 amps maximum measurable value
• USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
• 6 hardware UARTS (UART1,2,3,4,6,7)
• All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
• TF card for Blackbox logging
• Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
• Mounting Holes: Standard 30.5mm square to center of holes
• Weight: 9g

 

https://blog.seidel-philipp.de/holybro-kakute-f7-flight-controller-anschlussplan-wiringplan/

Manual:

http://www.holybro.com/manual/Holybro_Kakute_F7_Manual.pdf


 

Tekko32 4-in-1 35A ESC
Powerful 4in1 ESC with BLHELI32 firmware natively supports ESC Telemetry function.

Features:
4in1 ESC with 30.5×30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware.
This version features more CAPS to reduce power noise.
32bit ESC with BLHELI32 firmware
4PWM input
Voltage output (VBAT), ESC Telemetry(TELEM)
Supports Oneshot / Multishot / Dshot PWM
Supports damped light
NO BEC

Spec
Supports 3-6S lipo input
35A continuous current, 50A burst
Mounting holes 30.5×30.5mm
Size:55*40*6.4mm
Weight: 17g

Package includes:
1*Tekko32 4in1 ESC board
1* 8pin to 8pin 1mm pitch cable

Some Tips:
·     BLHeli_32 ESC Firmware Overview
·     GitHub

4-in-1 ESC on the motor pad side

Each motor’s 3 wires are to be soldered on the three pads dedicated to each motor M1, M2, M3 and M4. You will need to experiment to find the order that allows each motor to spin in the proper direction. If a motor is spinning in the wrong direction, swap two wires of the three wires going to the motor.